Spis treści

On/Off

After switching on the power supply (inserting the fuse, switching on the planer, switching on the additional switch), the tripmeter is ready for operation.
The tripmeter does not have a power switch.
In positions not related to measurements, in the absence of voltage on the yellow wire (ignition switch), the tripmeter turns off the screen.
Due to the non-volatile measurement memory that works even after the power is turned off, turning on the tripmeter can cause two independent states.
After turning on the power of the tripmeter that was turned off from the start screen – it will automatically start measuring.
After turning on the power supply of the tripmeter, which was turned off when it was taking measurements, it will continue them.

Rules for navigating the tripmeter menu:

  1. Move the tripmeter to the home screen position and press MENU for 3 seconds
  2. Press UP or DOWN to navigate through the menu or change a value in a submenu
  3. Press OK to enter the master branch submenu
    – press UP or DOWN to change the value
    – press OK to save the change and exit the submenu
    – press CLR to exit the submenu without saving the change
  4. Press MENU at the main menu item to exit the menu to the home screen and save changes to any settings.

The tripmeter works with two sensors of any design
The tripmeter has a continuous control of the sensors’ operation along with optical signaling
Operation of sensors in various configurations depending on the needs
Ability to count backwards

Starting measurements from the start screen

Operation of the function and the use of buttons in normal mode

  • When you see the start screen on the tripmeter screen
    – press the RUN button (displays will flash as a sign of readiness to start)
    – press the CLR button to start the measurements

Operation of the function and the use of buttons in the advanced mode

  • When you see the start screen on the tripmeter screen
    – press the RUN button (displays will flash as a sign of readiness to start)
    – by pressing the UP or DOWN and OK buttons briefly enter the TIMER value you enter the time in the format hh:mm:ss, e.g. if you enter the value 10500 it will mean 1h05m00s
    – if you do not want to enter the TIMER time, press OK during measurements, the TIMER time will count from 0
  • long press OK button
    – by pressing the UP and DOWN and OK buttons briefly enter the DELAY value you enter the time that will elapse from pressing the button to start the measurements until the actual start of the measurements in the ss format, e.g. if you enter 10, it will mean 10 seconds to start the measurements, i.e. 10 seconds to prepare the start.
  • press the OK button for a long time (displays will flash as a sign of readiness to start)
  • press the CLR button briefly to start the measurements
  • Start measurements from the standby screen
    – short press CLR, which will start the measurements from the standby screen
  • Deleting the short path
    – briefly press CLR, which will delete the short route TRIP
  • Switch between Travel, OS and Azimuth modes
    – press RUN briefly which will display the list of modes
    – press RUN to scroll through the modes
    – press OK to select and switch to another mode

Reset to factory settings

To reset the H-101 tripmeter to factory settings, follow the steps below:

  1. turn off the power to the tripmeter
  2. simultaneously press and hold (until further notice) the CLR and OK buttons
  3. power on the tripmeter
    • the tripmeter will turn on normally beeping 4 times
    • then it will beep twice as long
    • will reboot (release buttons)

Note: Resetting to factory settings will lose all user data and settings.

Option update

To update the options of the H-101 tripmeter, you must first have the current version of the software. You can then install an option update that is provided by the manufacturer. Copy the options file to a flash drive. We recommend that there is no other data on the flash drive and formatting is done in the FAT32 file system with default allocation settings, etc.

  • bring the tripmeter to the start screen position
  • insert flash drive
  • wait for the File ok confirmation to appear.

Firmware update

Firmware update is the process of updating the software. You can obtain the current versions of the software from the manufacturer. The software update does not change the purchased options. The firmware is secured by encryption.

To update the software:

  1. press MENU for a few seconds to bring the tripmeter to the home screen position
  2. when starting from the home screen [- – – -] skip step 1
  3. turn off the power to the tripmeter
  4. insert the flash drive into the tripmeter’s USB port
  5. power on the tripmeter
  6. 4 short beeps will confirm the detection of a new program version
  7. wait for the tripmeter to turn on (max. 30 seconds)

In case you don’t get 4 beeps after turning on the power:

  1. check if you copied the file
  2. check that the file name is still: firmware.bin
  3. change the flash drive to another one, possibly format it (FAT32, default allocation settings)
Scroll to Top