Na tej stronie dowiesz się:

Switching on/off

After the metrometer is powered on (inserting the fuse, turning on the heb, turning on the additional switch), it is ready for operation.
The metrometer does not have a power switch.
In positions that are not related to measurements, when there is no voltage on the yellow wire (ignition switch), the metrometer extinguishes the screen.
Due to the permanent memory of measurements that works even after power off, turning on the metrometer can cause two independent states.
After powering on the metrometer, which was switched off from the position of the start screen – it will automatically start measurements.
After powering on the metrometer, which was switched off when it realized measurements – it will continue them.

Rules for navigating the tripmeter menu:
1. bring the metrometer to the start screen position and press MENU for 3 seconds
2. press UP or DOWN to move ai through the menu or change the value in the submenu
3. press OK to enter the submenu of the main branch
– press UP or DOWN to change the value
– press OK to save the change and exit the submenu
– press CLR to exit the submenu without saving the change
4. press MENU at the main menu item to exit the menu to the start screen and save changes to any settings.

The metrometer works with two sensors of any design
The metrometer has a continuous control of sensor operation with optical signaling
Operation of sensors in various configurations depending on the needs
Possibility of counting “backwards”

Starting measurement from the start screen

Function operation and button usage in basic mode

When you see the start screen on the metrometer screen
– press the RUN button (displays will flash as a sign of readiness to start)
– press the CLR button, which will start the start of measurements

Function operation and button usage in advanced mode

When you see the startup screen on the metrometer screen
– press the RUN button (the displays will flash as a sign of readiness to start)
– by pressing the UP or DOWN and OK buttons briefly enter the TIMER time value
you enter the time in gg:mm:ss format, e.g. when you enter the value 10500 it will mean 1g05m00s
– if you don’t want to enter the TIMER time press OK
during measurements the TIMER time will count from the value 0
press the OK button long
– by pressing the UP and DOWN buttons and OK button short enter the value of DELAY
you enter the time that will elapse from pressing the button that starts the measurement to the actual start of the measurement in ss format, for example, when you enter 10 it will mean 10 seconds to the start of the measurement, that is, 10 seconds to prepare the start.
press OK button for a long time ( displays will flash as a sign of readiness to start)
press CLR button briefly which will start the measurement

Start measurements from the standby screen
– press CLR briefly, which will start measurements from the standby screen
Deleting the short path
– press CLR briefly, which will delete the TRIP short path
Switching between Commute, OS and Azimuth modes
– press RUN briefly which will bring up the list of modes
– press RUN to browse the modes
– press OK to select and switch to another mode

Reset to factory settings

To reset the H-101 metrometer to factory settings, follow the steps below:

switch off the power supply to the tripmeter
press the CLR and OK buttons simultaneously and hold them (until further notice)
switch on the power supply of the tripmeter
- the tripmeter switches on normally by beeping 4 times
- then beeps twice as long
- restarts (release buttons)

Note: Resetting to factory settings will result in the loss of all data and user settings.

Updating options

To update the options of the H-101 metrometer, you must first have the current software version. An option update can then be installed, which is provided by the manufacturer. Copy the options file to a memory stick. We recommend that there is no other data on the memory stick and the formatting is done in the FAT32 file system with default allocation settings, etc.

bring the tripmeter to the position of the start screen
insert memory stick
wait for File confirmation ok.

Firmware update

A firmware update is the process of updating the software. You can obtain the latest software versions from the manufacturer. Updating the software does not change the purchased options. The firmware is secured by encryption.

To update the software:

press MENU for a few seconds to bring the tripmeter to the start screen position
when starting from the start screen [- – – -] skip point 1
switch off the power supply to the tripmeter
Insert the memory stick into the USB connector of the tripmeter
switch on the power supply of the tripmeter
4 short beeps confirm the detection of a new programme version
wait for the tripmeter to switch on (max. 30 seconds)

In case you don’t get 4 beeps when the power is switched on:

check that you have copied the file
check that the file name is still: firmware.bin
change to a different memory stick, possibly format it (FAT32, default allocation settings)

Sending parameters to the repeater

When you start measuring or enter Azimuth mode, a default parameter is sent to the repeater. To manually send a different parameter:

press OK to send the parameter immediately, or leave the selected value – it will be automatically sent after 5 seconds.
Press and hold the MENU button, and then press the UP Arrow or DOWN Arrow button.
release both buttons. The status bar on the right side of the screen (above the word FILE) will show the active parameter.
press the arrow buttons until the name of the parameter you want to send to the repeater appears.
press OK to send the parameter immediately, or leave the selected value – it will be automatically sent after 5 seconds.